In case you’re searching for methods to make your audio sound skilled, it isn’t as laborious as it might look. On this tutorial, I will be going over some methods and instruments, in addition to sharing my common workflow to realize nice audio with Fairlight.
In terms of audio, there’s tons you are able to do, from shopping for new microphones to treating your room to create the absolute best setting. However typically, we simply have to work with what we have now.
At present I am utilizing a Sennheiser MKE 600 as my primary microphone after I’m taking pictures video. It is an incredible mic, albeit just a little pricy sitting round CA$400. No matter you will have, we will make it work. I’ve had nice experiences with Shure SM58 and RODE Video Mic Go, and each of these choices are $100 and below.
One other factor you will want is an honest pair of headphones or audio system to listen to your audio again. For me, that is just about an important device, though it does not imply you might want to exit and get a full setup. I stay in an condo, and whereas audio system are good, I discover my headphones the go-to device. At present, I am utilizing an previous pair of Shure SRH440. They seem to be a respectable set of entry-level cans that may get the job completed. No matter you will have is sweet sufficient. Even when you do not have headphones or audio system, you’ll be able to nonetheless make your audio sound higher by monitoring by way of your pc’s built-in audio system or utilizing an inexpensive pair of earbuds.
Let’s Get Began
For this tutorial, I will be utilizing a clip of audio that was recorded in my front room utilizing my MacBook’s inside microphone.
That clip with nothing completed to it is not even that dangerous. Let’s soar into Fairlight, and I am going to undergo a few of the steps I take to make it sound just a little extra skilled.
Step 1: Normalize Audio
The instance clip is peaking round -20 dB to -30 dB. You can see this stat in your mixer whenever you play by way of your clip. I need this to sit down round -8 dB or -10 dB. There’s a good way to regulate this by deciding on then right-clicking in your observe and discovering the choice Normalize Audio Ranges. Add your goal degree, -8 dB. All this does is alter your audio degree in order that the very best degree within the clip is the set goal.
Step 2: Compression
Inside the mixer, you will see an choice for Dynamics. That is the place you will discover a number of instruments: Expander/Gate, Compressor, and Limiter.
You’ll be able to activate the compressor by clicking on the title within the centre column. What this device does is compress your audio sign as soon as it hits a set level to assist handle peaking. All I am going to do right here is use the Make Up Acquire to deliver the quantity up and make the observe extra constant. In case you add an excessive amount of achieve, you will see a pink line within the graph. That is only a peak, and you should utilize Ratio to assist fine-tune your edit.
Step 3: Expander/Gate
You need to use the Expander or Gate to regulate your dynamic vary and cut back background noise, if in case you have any. Strive setting your threshold between -25 dB and -30 dB. I all the time attempt to use the expander first—it is rather less drastic, however as a result of I’ve a considerable quantity of background noise, I’ll use the gate. The gate drops/reduces every thing under your threshold.
Step 3: Equalization
This subsequent step is fairly essential, however there is a catch. Your audio goes to be completely different than mine. Try this tutorial all about EQ. For instance, that is how I edited the EQ for my clip.
Step 4: Multiband Compressor
So as to add this compressor, add an impact to your channel. Doing that is straightforward—simply comply with this pathway: Results (in your mixer) > Dynamics > Fairlight Results > Multiband Compressor. I usually do not change something for this impact. The default is fairly nice.
Step 5: De-Esser
The final device I exploit is the De-Esser. So as to add this impact, go to Results > Noise Discount > De-Esser. As soon as once more, I am utilizing the default as my start line. Due to my voice, I selected Male Ess from the dropdown choices. Underneath Frequency Vary, I exploit the narrowest choice and solely apply a small quantity. The way you deal with this impact depends upon the clip you might be modifying.
Conclusion
That is it! In spite of everything these changes, right here is the completed product of audio recorded straight from my pc in a loud condo. This can be a little bit of an excessive instance, and I would not suggest recording your audio this manner, however it’s a superb pattern of what is potential. This recording can be improved drastically with a easy microphone and a room that has extra sound insulation or privateness.
Extra Fairlight Assets
Share Your Craft on the Envato Boards
Have you ever used these methods and instruments? tell us by becoming a member of the Envato boards.
